Custom 4-1/4" Short Strat Tremolo Arm, DG Black Strat, Gilmour, Short Trem Arm

Custom Fabricated Stainless Steel Tremolo
Arms For Original Fender
®
Stratocaster
®
Tremolo Bridges
The featured length is the 4-1/4″ Gilmour length, but you have two other
lengths to choose from, intermediate 5-1/4″ and standard 6″.
The Three Tremolo Arm Length Options Compared To Each Other – Shown With
Vintage Cream Tips
The Six Plastic Tip Color Options
Tip colors shown are close approximations to the one you’ll receive, they are not genuine Fender
®
and colors may vary from original Fender® colors. Also, with variances in production
runs and your particular devices screen color renderings your actual tip color
may vary slightly from how you see it above. These plastic tips unscrew, so you can always change them.
Our tremolo arms are fabricated from 303 stainless steel for genuine Fender
®
Stratocaster
®
tremolo
bridges only and are threaded for a screw-in attachment
to the bridge in UNF 10-32 or metric 5mm (M5 x 0.8) threading.  They are not chrome plated, they are solid 303 stainless steel with a satin
finish.
These
tremolo arms are
NOT designed to fit a Squire® Strat®, clone Strat® or any aftermarket bridge, so
DO NOT
purchase for any Squier®, clone or replica Strat® or for any aftermarket
tremolo bridge.
They are designed for original genuine
Fender® Strat® tremolo bridges only.
Our
tremolo arms are exclusively designed for a genuine Fender®
Strat
®
tremolo bridge that is setup as
free-floating. The free-floating bridge setup allows the underside back edge of the bridge top plate to
be lifted up off the body by approximately 1/8″, this is how just about all Strat’s®
come setup from Fender
®
. 
The free-floating bridge setup allows you to increase or decrease string tension
thus raising or lowing pitch by lifting up or pressing down on the tremolo arm,
this setup is what allows for the best vibrato effect. Our tremolo arms normal
tip-to-pickguard distance is based on this free-floating bridge setup, if you do
not currently have your bridge setup as free-floating then you will need to set
it up as such before installing one of these tremolo arms.
If you choose not to setup your bridge as
free-floating, then do not purchase one of these tremolo arms.
Tremolo arm tip-to-pickguard distance is a personal preference measurement and
our tremolo arm design fits most people most of the time, but due to variances
in ones hand size and playing style, its possible you may
find that the tremolo arm tip may sit a little high or low from the pickguard
surface for your taste and this is a normal characteristic that your specific
setup may require a small adjustment to the bend angle of your tremolo arm. 
After evaluating your new tremolo arm and you think you need an adjustment to
the tremolo arm tip-to-pickguard distance send us an email before attempting any
adjustment to your tremolo arm to prevent damage and / or breakage.  We will
assist you in explaining what you need to do to make the adjustment correctly.
Our 5-1/4″ and 6″ length tremolo arms have a similar design to an original
Fender® American Standard Strat
®
tremolo arm
in regards to the up-sweep portion of the tip
end of the tremolo arm. The up-sweep is the angle that the bend closest to the
plastic tip sweeps up away from the pickguard surface. Our  5-1/4″ and 6″
length tremolo arms have a 30 degree angle of up-sweep, where an original Fender® American
Standard Strat
®
tremolo arm
has a slightly increased angle of 39 degrees of up-sweep. Our short 4-1/4″ Gilmour
style length tremolo arm has less of an angle of up-sweep at only 15 degrees and this is indicative of this specific artist
series tremolo arm. You’ll notice this difference in up-sweep angles visually in the tip bends by closely
reviewing the above
photograph showing all 3 lengths of tremolo arms.
As you will notice in the above photograph showing all 3 lengths compared, each
different length tremolo arms first bend as it comes up and out of the bridge is
bent to a different degree angle of bend. This is by design to facilitate the
same tremolo arm tip-to-pickguard distance no matter which length you may
select. Each length will present the tip end of the tremolo arm at approximately
the same distance down to the pickguard surface when in the same playing
position.
Important Points of Reference of
Tremolo Arm Lengths, Styles and Designs:
The typical OEM Fender®
Strat
®
tremolo arm is approximately 6″ in length, some models may vary by plus or minus 1/2″.
David Gilmour’s short tremolo arm is published in Phil Taylor’s
book “
The Black Strat
” as custom shortened to 4-1/4″ in length.
The tremolo arms offered here
will
NOT
fit the
Fender
®
American Deluxe, Elite, Ultra or Professional Strat
®
, they
accept a pop-in tremolo arm.
The tremolo arms offered here are
NOT
chrome plated, they are solid 303 stainless steel
with a satin finish.
We do
NOT
fabricate these tremolo arms in the 6mm (M6 x1.0) screw-in attachment threading for Squier’s.
We do
NOT
accept special requests for customization’s or alterations to these original
tremolo arm designs.
Selecting The Correct “
ATTACHMENT THREADING
”
For Your Genuine Fender® Strat®:
American Strat
®
10-32:
These tremolo arms will fit the
Fender® American
Standard Strat
®
with the 2-point synchronized tremolo bridge, American Special
Strat
®
, American
Vintage Re-Issue Strat
®
or any genuine Fender
®
American Strat
®
tremolo
bridge that accepts a 10-32 threaded screw-in tremolo arm.
Metric 5mm (M5 x 0.8):
These tremolo arms will
fit original genuine Fender
®
Mexican and Japanese Strat’s
®
tremolo bridges that accept a metric 5mm threaded screw-in tremolo arm.
IMPORTANT NOTE:
If you have one of the original Fender
®
half-thickness, lightweight/cast zinc tremolo blocks on your import
Strat
®
bridge
then these custom tremolo arms offered here will not have the proper bend angle for that model of
bridge, those bridges accept the tremolo arm into the tremolo block at 10 degrees
of angle
different than the typical Strat
®
tremolo bridge than what these tremolo arms offered here are designed for. You can confirm
this by the removal of the back plate on your Strat
®
and looking at the bottom of
your tremolo block where the tremolo tension springs clip on, the tremolo block
will only be 1/4″ thick and that is not what you want to see, so
DO NOT
purchase
one of these tremolo arms for that bridge.
These
tremolo arms are
NOT designed to fit a Squire® Strat®, clone Strat® or any aftermarket bridge, so
DO NOT
purchase for any Squier®, clone or replica Strat® or for any aftermarket
tremolo bridge.
They are designed for original genuine
Fender® Strat® tremolo bridges only.
If you are unsure of the correct tremolo arm
screw-in attachment
threading for your Fender
®
Strat® you will need to contact Fender customer service to determine which is the correct one for your bridge, but ultimately it
is your responsibility to know which is the correct tremolo arm for your guitar
and place your order accordingly.  Don’t just order one to see if it fits and then return it because it doesn’t fit. We’re not in the business of sending out parts for evaluation and returning what you can’t use or don’t fit.
Tremolo Arm Option Selections
Two Different Screw-In Tremolo Arm Attachment Threading Options:
UNF 10-32
Metric 5mm (M5 x 0.8)
Three Different Tremolo Arm Length Options:
4-1/4″ Gilmour Black Strat®
style shortened length
5-1/4″ Intermediate length
6″ Standard length
S
ix Different Plastic Tip Color Options:
(plastic tips are not original Fender
®
and colors may vary from original Fender
®
colors)
White
Parchment
Mint Green
Cream
Vintage Cream
Black
Right or Left Handed Tremolo Arm Versions:
Right handed
Left handed
Below is OverDrive
Custom Guitar Works’ Black Strat® inspired replica
project with our 4-1/4″
tremolo arm installed along with our custom built Black Strat®
Fully
Loaded Complete Pickguard Assembly.
For complete Gilmour inspired Black
Strat
®
project details you can view it on the
Gilmour Black Strat® Inspired Parts page at OverDrive Custom Guitar Works.
International Buyers – Please Note
Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyer’s responsibility.
Please check with your country’s customs office to determine what these additional costs will be prior to bidding or buying.
INTERNATIONAL
BUYERS – PLEASE NOTE:
All orders ship via the USPS (United States Postal
Service) but once your order arrives in your country it is handed off to
either your countries official postal delivery service or a contracted
courier such as DHL.  To receive the most up to date/current tracking
status and delivery requirements once your shipment has arrived in your
country you must use your countries postal service
or contracted delivery couriers tracking services.  It is the customers
responsibility to actively follow your shipments transit progress
through all means of tracking provided by your countries delivery service
or contracted courier
for a parcel that originated from the USPS shipping service. Simply go to
your countries postal delivery services or contracted delivery couriers web site and use their tracking
service to enter in the original tracking number you were given, they will
be able to provide you with additional information about your shipment
once it has arrived in your country and has entered or cleared customs
inspection. Do not delay in making any required arrangements for delivery or
your shipment will be returned to us as “Unclaimed”.
This item is not endorsed by David Gilmour and is only
referenced and described in Phil Taylor’s book “The Black Strat” and as similar in style and length
that is used on his Black Strat  guitar.
This item is not endorsed by Fender Musical Instruments
Corp., it is offered as a similar style custom replacement part for
your guitar.
Fender®, Strat® and Stratocaster®
are registered
trademarks of the Fender Musical Instruments Corp.
OverDrive Custom Guitar Works is not affiliated with Fender Musical
Instruments Corp.